limiting values absolute maximum rating item symbol unit conditions V10P10 repetitive peak reverse voltage v rrm v 100v average rectified output current i o a 60h z sine wave, r- load, t a =25 10 surge(non-repetitive)forward current i fsm a 60h z sine wave, 1 cycle, t a =25 275 current squared time i 2 t a 2 s 1ms t 8.3ms t j =25 313 storage temperature t stg -55 ~ +150 junction temperature t j -55~+150 thermal resistance(typical) r j-c /w between junction and case 15 electrical characteristics ta=25 unless otherwise specified item symbol unit test condition min typ max peak forward voltage v fm v i fm =10.0a,tj=25 i fm =10.0a,tj=125 reverse breakdown voltage v br leakage current ir ma vr=100v tj=25 vr=100v tj=125 features high surge forward current capability low power loss, high efficiency i f av 10a v rr m 100v applications switching power supply industry photovoltaic solar cell protection schottky rectifier m ou nti ng pad lay out .2 6 0(6 . 60 ) .2 5 2(6 . 40 ) .2 1 5(5 . 40 ) .2 0 5(5 . 20 ) .01 4 (0 . 35 ) .01 0 (0 . 25 ) .03 9 (1 . 00 ) .03 1 (0 . 80 ) .0 7 5(1 . 90 ) .0 7 1(1 . 80 ) .0 45( 1 .1 5) .0 41( 1 .0 5) bo tto m dimensions in inches a nd (m ill imeters) to-277/powerdi5 . 16 1 (4. 10) . 15 4 (3. 90) . 075 ( 1. 90) . 067 ( 1. 70) .1 91 ( 4.8 6) . 132 ( 3. 36) .0 5 5(1 . 40 ) .0 5 5( 1 .40 ) .07 2 (1 . 84 ) .0 33 ( 0.8 5) left pin right pin bottom side heat sink note: pins left & right must be electrically connected at the printed circuit board. ? V10P10 pb free plating product V10P10 10 ampere lower vf miniature surface mount schottky barrier rectifier pb ? 2006 thinki semiconductor co., ltd. http://www.thinkisemi.com/ page 1/2 rev.05 - 0.61 0.65 - 0.54 0.58 v ir=0.1ma 100 - - - - 0.1 - - 10
rating and characteristic curves ? 2006 thinki semiconductor co., ltd. http://www.thinkisemi.com/ page 2/2 rev.05 0.4 0.6 0.8 1.0 0.1 10 1.0 ta=25 100 00.2 instantaneous forward current (a ) instantaneous forward voltage (v) fig.3: forward voltage 0 20 40 60 80 100 0.01 0.1 1.0 10 100 tj=125 tj=25 fig.4: typical reverse characteristics percent of rated peak reverse voltage (%) instantaneous reverse current (ma) 0 0 50 100 150 2.0 4.0 6.0 8.0 10.0 average forward output current (a) ambient temperature () fig.1: io-ta curve 1 0 2 10 20 100 60 120 180 8.3ms single half since-wave jedec method peak forward surge current (a) number of cycles fig.2: surge forward currrent capadility 240 300 360 fig.2: surge forward current capability 8.3ms single half sine-wave jedec method ? V10P10
|